Your Plumbing Crash Course: A Necessity for Bathtub Installation
Your Plumbing Crash Course: A Necessity for Bathtub Installation
Blog Article
Presented here in the next paragraph you'll find a good deal of sound tips involving Installing A Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately difficult project. If the old tub is conveniently obtainable, the task can move rapidly; if you have to open up a wall to eliminate the old bathtub and position the new tub, the task is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the task and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This write-up will help you set up a new bath tub in your washroom if you have currently bought a new tub as well as don't require to change the plan of your previous water pipelines.
Your devices as well as material checklist must consist of the following:
Preparing for the Installation
To start with, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will originate from the pipes. Once the supply pipelines have been removed, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the bathtub in the called for placement. The wood boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub till the level reads level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Switch on the water system as well as check all joints and new pipework for leaks and also tighten them if essential. Load the tub as well as also inspect the overflow electrical outlet as well as the normal outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the bath tub should wait till the bathtub has actually been utilized at least once as this will settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and also the sink. Protect the faucet in position with the manufacturer supplied backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The former kind must be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a stiff seal, causing the water to permeate the wall between the bathroom and the tiling, resulting in complications with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to enable the movement experienced when the tub remains in use. The sealer can break fairly very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on another web page. Sharing is caring. You won't know, you might be doing someone a favor. Thank-you for going through it.
Emergency? We're here! Report this page